Revere Roof Pros provides professional metal roofing in Revere, MA for residential and commercial properties across Boston's inner North Shore. We install standing seam, and we also spend a fair amount of time arguing owners out of it. In this city metal usually gets proposed for the part of the roof that is not leaking. The street face is what you see. The flat deck behind it is what fails.
Spending twenty thousand dollars on a mansard in twenty-four gauge while the main deck keeps a twenty-year-old membrane is a decision about the street, not about water. If that is genuinely what you want, say so and we will price it properly, but we will not present it to you as a repair, and the membrane's remaining life goes in the same document so the choice is made with both numbers visible.
Where metal earns its keep here is on the small awkward planes. Rear porch roofs, bay window tops, stair bulkhead caps and dormer cheeks are all short runs with a lot of terminations packed into them, and a mechanically seamed or concealed-clip panel in those places will outlive anything else you can reasonably put there. Those are also the planes where a shingle detail was never really going to work.
The details that matter are the ones nobody photographs. Panels have to be free to move against a fixed clip line, the ridge and eave closures must shed rather than dam, and every penetration wants a curb instead of a boot lapped onto a flat pan. Panel gauge is the last item on that list rather than the first, whatever the brochure leads with. Nobody should be surprised by that in year three.
Attached and near-attached buildings add a constraint most of the trade never meets. A panel run that discharges over a party wall, or onto an abutter's roof three feet away, is a dispute waiting to happen. We set the discharge point during design and show it on the drawing before anything gets ordered or bent. Neighbors remember which contractor asked first.
If your building is a three-family, remember this is base-code work and the permit needs an unrestricted supervisor. A metal quote arriving without that is a quote for a building nobody has looked at properly, however good the samples were. We put the class on the estimate so you can check it against the permit.
Our licensed and insured team brings the right materials and equipment to every job — an unrestricted CSL number entered on a three-unit permit application, a granulated SBS cap sheet bedded in cold adhesive, tapered EPS crickets built behind a rear chimney stack, a shingle-to-membrane transition worked into the mansard eave line, a party-wall parapet capped in 20-ounce lead-coated copper, two-piece surface counterflashing screwed to a brick firewall — and backs the work with a written workmanship warranty. We serve Revere and nearby communities including Chelsea, Winthrop, Everett, Malden.
What We Handle
Everything our metal roofing in Revere covers
One crew, one point of contact, and the full range of metal roofing work in Revere, MA. If it is on this list we do it in house rather than handing it to a subcontractor:
- metal roofing Revere MA
- standing seam roof Revere
- metal roof installation Revere MA
- metal roof cost Revere
- steel roofing contractor Revere MA
- standing seam installer Revere
- metal roof two family Revere
- metal roofing Suffolk County
- aluminum roofing Revere MA
- metal roof mansard Revere
- snap lock metal roof Revere
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Revere services.
Materials, equipment and how we do metal roofing
The difference between metal roofing that lasts and metal roofing that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with an unrestricted CSL number entered on a three-unit permit application, a granulated SBS cap sheet bedded in cold adhesive, tapered EPS crickets built behind a rear chimney stack, a shingle-to-membrane transition worked into the mansard eave line, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Revere job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. Years of roofing work in Boston's inner North Shore means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do metal roofing outside Revere
Revere Roof Pros covers Revere and the surrounding communities of Boston's inner North Shore. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Metal Roofing in Chelsea, MA — Suffolk County, population 40787
- Metal Roofing in Winthrop, MA — Suffolk County, population 19316
- Metal Roofing in Everett, MA — Middlesex County, population 49075
- Metal Roofing in Malden, MA — Middlesex County, population 66263
- Metal Roofing in Medford, MA — Middlesex County, population 59659
- Metal Roofing in Melrose, MA — Middlesex County, population 29817
Start on the Revere Roof Pros homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why Revere Chooses Revere Roof Pros
- ✓We establish the dwelling unit count before quoting, because it decides the code path, the license class and the paperwork, and most bids in this city never mention it at all.
- ✓Our estimates carry the Construction Supervisor License number and its restriction class, so you can check that the person signing your permit is actually allowed to sign it.
- ✓We write scopes with quantities and fastener patterns so you can take our document to two other roofers and receive numbers that describe the same roof.
- ✓Inspection fees are billed and stay billed, never netted off a later job, because that is the only way to be certain the report you receive is an opinion and not a pitch.
The standards behind metal roofing
Quality here is not a matter of opinion — it is written down. The metal roofing work we do in Revere follows published industry standards: NRCA publishes the Roofing Manual, the industry's reference for details and slope minimums, and Asphalt Roofing Manufacturers Association sets the shingle application and ventilation guidance the warranties reference. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every metal roofing project in Revere gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free metal roofing free estimate in Revere, or request a quote and we'll get right back to you.